NEW Walther P22 with Two 10-Round Magazines. This 22LR pistol is all black and has a 3.42" barrel. The ambidextrous safety is also a hammer decocker. It has interchangeable backstraps and is very comfortable in the hand.
The Catco Sterling 9mm SMG submachine gun is constructed entirely of steel and plastic and has a shoulder stock, which folds underneath the weapon. There is an adjustable rear sight, which can be flipped between 100 and 200-yard settings. Although of conventional blowback design firing from an open bolt, there are some unusual features: for example, the bolt has helical grooves cut into the surface to remove dirt and fouling from the inside of the receiver to increase reliability. There are two concentric recoil springs that cycle the bolt, as opposed to the single spring arrangement used by many other SMG designs. This double-spring arrangement significantly reduces “bolt-bounce” when cartridges are chambered, resulting in better obturation, smoother recoil, and increased accuracy. Additionally, the Sterling uses a much-improved (over the Sten) 34-round curved double-column feed box magazine, which is inserted into the left side of the receiver. The magazine follower, which pushes the cartridges into the feed port, is equipped with rollers to reduce friction. The bolt feeds ammunition alternately from the top and bottom of the magazine lips, and its fixed firing pin is designed so that it does not line up with the primer in the cartridge until the cartridge has entered the chamber. The Sterling employs a degree of what is known as Advanced Primer Ignition, in that the cartridge is fired while the bolt is still moving forward, a fraction of a second before the round is fully chambered. The firing of the round thus not only sends the bullet flying down the barrel but simultaneously resists the forward’s movement of the bolt. By this means it is possible to employ a lighter bolt than if the cartridge was fired after the bolt had already stopped, as in simple blowback, since the energy of the expanding gases would then only have to overcome the bolt’s static inertia (plus spring resistance) to push it back again and cycle the weapon; whereas in this arrangement some of this energy is used up in counteracting the bolt’s forwards momentum as well, and thus the bolt does not have to be so massive. The lighter bolt makes not only for a lighter gun, but a more controllable one since there is less mass moving to and fro within it as it fires. The suppressed version of the Sterling (L34A1/Mk.5) was developed for covert operations. This version uses a ported barrel surrounded by a cylinder with expansion chambers. The Australian and New Zealand SAS regiments used the suppressed version of the Sterling during the Vietnam War. It is notable for having been used by both Argentinian and British Special Forces during the Falklands War. A Sterling was used by Libyan agents to kill WPC Yvonne Fletcher outside the Libyan Embassy in London, which sparked the 1984 siege of the building. The Sterling has a reputation for excellent reliability under adverse conditions and, even though it fires from an open bolt, has good accuracy. With some practice, it is very accurate when fired in short bursts. While it has been reported that the weapon poses no problems for left-handed users to operate, it is not recommended without the wearing of ballistic eye protection. The path of the ejected cartridge cases is slightly down and backward, so mild burns can occasionally be incurred by left-handed shooters. A bayonet of a similar design as that for the L1A1 Self-Loading Rifle was produced and issued in British Army service but was rarely employed except for ceremonial duties. Both bayonets were derived from the version issued with the Rifle No. 5 Mk I “Jungle Carbine”, the main difference being a smaller ring on the SLR bayonet to fit the rifle’s muzzle. When mounted, the Sterling bayonet was offset to the left of the weapon’s vertical line, which gave a more natural balance when used for bayonet-fighting. For a right-handed shooter, the correct position for the left hand while firing is on the ventilated barrel-casing, but not on the magazine, as the pressure from holding the magazine can increase the risk of stoppages, and a loose magazine can lead to dropping the weapon. The barrel-casing hold provides greater control of the weapon, so the right hand can intermittently be used for other tasks. A semi-circular protrusion on the right-hand side of the weapon, approximately two inches from the muzzle, serves to prevent the supporting hand from moving too far forward and over the muzzle.
37" Rolling Evil Eye Cane Sword With Skeletal Hand Handle. In the 18th century the cane replaced the sword as an essential part of a gentleman's attire. While the cane was used as a walking stick it could also be used as a sword, or contain hidden compartments for alcohol or a firearm. The great men of the last two centuries have carried canes, from Sherlock Holmes, to Gregory House and of course Scrooge McDuck. Every Gentleman Requires a Cane. This cane is not a substitute for a medical walking device. The cane shaft has been constructed from steel with a black glossy finish. Hidden inside of the black metal shaft is a 12” hidden blade made of stainless steel, which can be accessed by unscrewing the handle. The bottom of the cane features a tough rubber gripper. The head of the cane has been constructed from steel with Rolling Evil Eye With Skeletal Hand Handle. Cane Overall Length: 37" Blade Length: 12" Handle Length: 4" Handle Width: 2" Cane Shaft Material: Steel Cane Head Material: Steel
CCI BLAZER BRASS 9MM LUGER AMMO 124 GRAIN FULL METAL JACKET - 5201 CCI Blazer Brass 9mm Luger Ammo 124 Grain Full Metal Jacket Newly manufactured 9mm ammo here in the United States, that features a full metal jacket copper plated bullet, brass casing, non-corrosive primers. Made by the same company that manufactures Speer Lawman 9mm ammo as well as the Federal American Eagle 9mm ammunition using same great quality components and manufacturing equipment. If you choose to reload your 9mm ammo, CCI Blazer Brass offers virgin brass that can be reloaded up to 5 times due to its high quality and low mixtures of other materials. Trusted CCI has gone above and beyond with the Blazer Brass line! With the same high standards that shooters have come to know and love with standard Blazer ammo, the Blazer Brass line gives the benefit of a brass casing making it reloadable. 9mm Luger by CCI are an excellent choice for target practice or just plinking around at the range. CCI Blazer Brass 9mm Luger is a new production, non-corrosive, re-loadable ammunition with boxer primers and brass casing. 9mm ammo is by far the most popular gun cartridge in the world. Recently adopted by the FBI and other law enforcement agencies, 9mm ammunition is perfect for target shooting and personal protection as well. 9mm ammo is fun to shoot, offers relatively low recoil and yields great target results. CCI Blazer Brass 9mm Luger is a new production, non-corrosive, re-loadable ammunition with boxer primers and brass casing. 9mm Luger by CCI are an excellent choice for target practice or just plinking around at the range. MPN 5201 UPC 76683052018 Manufacturer CCI AMMUNITION Caliber 9MM LUGER Bullet Type Full Metal Jacket Muzzle Velocity 1090 fps Muzzle Energy 327 ft lbs Primer Boxer Casing Brass Casing Ammo Rating Target and Practice 9mm Luger Ammo
American Civil War era hand-made cavalry sword. The 34.25 inch blade is crafted from thick high quality steel to replicate the saber and is 4mm thick. It has a factory edge and has been mirror polished down to perfection. The Seal of the United States has been engraved into the blade, along with the designs representing the pride and courage of those who fought for their heritage. On one side of the blade, the words E Pluribus Unum are engraved, and the other side has U. S. engraved into the steel. The handle is wrapped in black leather and features the authentic wound wire that is traditionally expected on a sword of this caliber. Weight has been added to the mirror polished brass pommel to balance the overall handling of the sword. An authentic hand made steel sheath is included with this gorgeous sword. The sheath features the standard loops for securing it to your effects and displaying it properly. Overall Length: 40.5 Inches. Blade Length: 34.25 Inches. Blade: Saber, Factory Edge, Mirror Polished, High Quality Steel, 4mm Thick. Handle: 6 Inches, Black Leather Wrap, Golden Wire Wound, Brass & Steel Tang Core. Guard: Polished Golden, Brass, Full Wrap. Pommel: Polished Golden, Brass, Weighted. Sheath: 36.25 Inches, Hand Made, High Quality Steel, Looped. Engraved: "US", "E Pluribus Unum." Features: 100% Handmade, 100% Polished. Please note: You must be at least 18 years old to purchase the products on this website. Swords, Knives and Daggers, its employees or associated companies assume no responsibility for injury, damage or loss incurred by use of any merchandise sold on this website. Compliance with local , state and federal laws and/or statutes is the responsibility of the buyer. Purchase of merchandise from Swords, Knives, and Daggers implies agreement to the above statements by buyer.
The bandit of Sherwood Forest, Robin of Locksley, is fabled to have stolen from the rich to help the poor. The legendary outlaw and his band of followers engaged in countless mischievous adventures that frustrated the evil Sheriff of Nottingham. Leather sheath is included with the purchase of this high quality sword.
It’s a hoot to shoot for sure and maybe more so than my SP5 (just maybe). So trying out a few options and started farkling out the PDW. Starting out with the following: Rear Drum (thx to @ Indreams84) Magpul forend/handguard HS1 finger light (green laser). Had to dremel out a hole for HS1 laser to poke/emitt through. Worked out great. JMAC Brace 8” raised arm bar 1913 SigMech folder Cheekweld affixed to top of brace (holes are predrilled and threaded) Gearworks Tailhook MOD1C Also saw the B&T retractable stock at LGS as another option that I’m going to ponder on: Per the measurements it seems that when retracted with MAGPUL forend/handguard appears to be issue. It would appear to be an unfavorable check rest but guess one can adjust and get used to it. It would appear the small end, would not seat great in shoulder/pec area, but again guess you can find a good area to pocket it into and get used to it quickly. Appears to retract really nice and seems compact and extends easily, and seems like great lockup with very minor up/down flex, hopefully minimal rubbing along body frame. so will also soon consider the Vertical grip and will need to pay it visit at the LGS soon again while pending the process. The JMAC Brace Pros: It’s a Brace and cheek hold is really comfortable and supportive. if you wanted to add an RMR/Optic it’s adjustable to slide up and down via the pic-rail and sig mech. I ended up cutting out the foam and was able to fit in it’s folded condition. It’s tight and although does fully seat, it closes and works out fine. Let’s see your SP5K-PDW Stock or Brace here in order to see the various options out there for the PDW.
The full-sized MP5 SMG from Heckler & Koch is already quite portable, but some special forces units wanted an even smaller weapon. Thus, the MP5K was born, a concealable weapon that can pour rapid fire immediately. Umarex’s airsoft replica is entirely accurate, though the caliber markings are obviously different to denote its airsoft status. Otherwise, the weapon is identical to the original, aside from an orange tip. It has an aluminum upper receiver and barrel assembly, while the lower receiver is a polymer. It’s a very light PDW and can be shot one-handed. The pistol grip is necessary for such a weapon since rapid fire must be controlled to prevent wasting ammunition. While it comes without a shoulder stock, the MP5K can accept any H&K MP5 stocks. The iron sights are permanently mounted on the gun. However, there’s a bracket for a short length of Picatinny rail. Umarex includes a Ver 3 Full Metal gearbox for the best performance, and it’s entirely upgradeable if you want more out of this weapon. The adjustable hop-up lets you alter BB flight paths as well. Specifications: 280-310 FPS with 0.20g BBs 200 rounds in the magazine AEG Officially licensed by Heckler & Koch Adjustable hop-up Two stocks included 9.6V Small Stick battery and charger not included Semi-auto, full-auto, and safe modes Note: Battery & Charger DOES NOT come with purchase of rifle (9.6V Small Stick battery Battery Recommended)
The Umarex Elite Force Glock 17 is a phenomenal addition to Airsoft skirmishes. The gun jumps out of the box with a classic design. Far from subtle with the symbols, the Glock trademarks are molded into the pistol’s frame and etched onto the slide. The external components are a major reason why Airsoft players will adore this weapon. The frame is made of high-density polymer, whereas the slide is reinforced with aluminum alloy – both of which add to the gun’s outstanding durability. Additionally, the Glock 17 features an ergonomically textured grip to ensure better handling, allowing you to keep the gun steady while firing and to get a better feel. Plus, the pistol is more versatile than its predecessors owing to the removal of finger grooves. There’s also the conveniently designed slide that lets you handle the weapon more comfortably. In particular, the slide is serrated and makes for effortless racking of the gun, which can save time on the battlefield. You also get to use a tough full-metal framed magazine with a decent capacity of up to 23 rounds. The magazine’s push-button release system is convenient and allows the shooter to reload quickly. The pistol lets you make lots of modifications to enhance your shooting experience. The under-rail can hold various tactical accessories, such as lasers and flashlights. You can also adjust the hop-up system to decrease or increase your BB spin. Last but not least, there’s the streamlined trigger safety designed to prevent misfires, and the gas blowback operation replicates realistic recoil. Features: Material - Metal Slide and Polymer Frame Operation – Gas Blowback Muzzle Velocity – 0.20g Ball Bearings at 325 FPS Length – eight inches Hop-Up: Adjustable Color: Black Magazine Capacity – 23 Rounds (Works with VFC and Umarex Glock Magazine)
Hatsan Escort semi-auto. Latest (2013) PS model, Black Synthetic, with Fast Load System and Smart Valve, C/W stock spacers allowing cast and length adjustment from 14 1/2" to 15 1/4". 3" magnum. Supplied with box, 5 external multi-chokes, key & accessories.
Description: Harrington & Richardson Reising, model 50, 45acp, fully transferable, no restrictions for the transfer. This is in refurbished condition, the wood is in great shape, has sling swivels, the receiver is in great condition, see the pictures, bore is good, this is a select fire, fully automatic, comes with four 20rds H&R magazines and four 40rnd. The hard case is included. This item must be transferred to an FFL class 3. The price listed is a cash price; no credit cards for this purchase. By committing to buy this item or gun you are saying that you are aware of all of the laws and restrictions in your state and you can lawfully own this item or gun. Payment must be received within 5 days. Transaction must be completed within 10 days or the item will be reposted. DO NOT COMMIT TO BUYING THE ITEM UNTIL YOU HAVE ASKED ALL QUESTIONS. Please ask all questions prior to purchase. Items are sold as is. The spare parts shown are the original parts as the new ones have been installed. I have a video available showing full auto fire. This will ship to your Class 3 dealer after full payment. There is a 3-day inspection allowed with full refund minus shipping if you are not satisfied. Buyer pays all shipping costs.
Arabian Sands Sabre Sword & Sheath - BK1335 This Arabian Sands Sabre Sword is unlike any sword in your collection! Get yours today! Features: Extra wide 13" heat tempered 440 stainless steel blade Solid wood grip Heavy brass guard and pommel Includes leather sheath 17 3/4" overall Please note: You must be at least 18 years old to purchase the products on this website. Swords, Knives and Daggers, its employees or associated companies assume no responsibility for injury, damage or loss incurred by use of any merchandise sold on this website. Compliance with local , state and federal laws and/or statutes is the responsibility of the buyer. Purchase of merchandise from Swords, Knives, and Daggers implies agreement to the above statements by buyer.